Laboratory Equipmentss

Product Details:

It is general-purpose machine and found very useful for mixing or agitation ingredients, solution in flasks, bottles, beakers and Kahn racks etc. Upper tray covered with rubber floor and sides of the tray are slotted to take parallel and cross bars cover with rubber to hold flasks, bottles beakers, Kahn racks etc. The bars are tightened with washers and fly nuts can be adjusted as per the requirement.

 

The machine can accommodate Kahn racks, bottles or flasks of different sizes by adjusting the compartments with the help of rods supplied with the machine. Fitted with ¼ HP motor and having mechanical adjustments for adjusting the motion.

 

Special Features:

• D.c. motor special system shaker to work on 220 volt a.c. for variable and smooth function
• Equipped with ¼ HP motor.
• No of oscillations: at 280 ± 5 oscillations per minute.
• Supplied with top platform rods, ON/OFF switch, plug and cord.
• Fitted with heavy duty motor to work on 220V, AC 50 Hz single phase
• Timer 0-30 minutes (optional)
• Microprocessor based RPM control (optional)

 

Product Details:

Quartz Water distillers produce highly treated and disinfected water for laboratory usage. The distillation process removes minerals and microbiological contaminants and can reduce levels of chemical contaminants.

 

Water distillers are neither intended to treat water that is visually contaminated nor intended to convert waste water to safe, microbiologically.

 

Working Principle:

A water distiller works by boiling water into water vapour, condensing it and then returning it to its liquid state. It is collected in a storage container.

The process occurs in several steps:

• Municipal or well water is manually or automatically fed into the distiller unit’s boiling chamber.
• A heating element in the boiling chamber heats the water until it boils.
• The steam rises from the boiling chamber. Volatile contaminants (gases) are discharged through a built-in vent. Minerals and salts are retained in the boiling chamber as hard deposits or scale.
• The steam enters a coiled tube (condenser), which is cooled by cool water.
• Water droplets form as condensation occurs.
• The distilled water is collected in a storage tank. If the unit is an automatic model, it is set to operate to fill the storage tank.

 

Features:

• Quartz distiller, Demountable boiler.
• Compact design, Dual safety cutout(optional).
• High purity, low conductivity, Pyrogen free distillate.
• Easy service and maintenance due to Demountable model.

 

Distilate Qty. Specifications:

* Due to difficulties in measuring PH for high purity water and the doubtful significance of the value obtained, PH is not specified for high purity water.

Feed Water Analysis:


Capacity:

• 0.5 ltr / hr
• 1.0 ltr / hr
• 2.0 ltr / hr
• 3.0 ltr / hr
• 4.0 ltr / hr
• 5.0 ltr / hr

Note:

• The results mentioned in specifications are obtained under standard laboratory conditions and by using Weiber water treatment Cartridge for raw water.
• The use of treated water, as feed to boiler, is highly recommended to prevent scaling in the boiler, to improve the quality of distillate and for longer life of the equipment.
• The above equipment produces Grade 1 reagent quality water

 

 

 

Product Details:

The equipment has a very heavy casted top made of high grade stainless steel block of grade SS-304 with room for heating 40 digestion tubes made of highly energy efficient borosilicate glass of 75 ml each. The suitable value heating element are made of high grade kanthal A-I non magnetic wire. These heaters are strategically placed throughout the chamber for uniform temperature distribution through the chamber. The outer casing of the equipment id made of thick PCRC sheet duly pre treated with primers for rust proofing and painted with attractive stove enamel paint or powder coated. The 75mm gap between the two walls is filled with mineral wool to have minimal thermal loss and maximum energy efficiency.

Temperature Control:
Temperature is controlled through electronic solid state temperature controller cum indicator or micro processor based digital temperature controller cum indicator.

Control Panel:

The control panel is fitted at the side of the equipment, it comprises of mains on/off switch, neon power indicator light, heater on/off indicator light, digital temperature controller cum indicator.
 
Standards Models:
Model Acm-54096- W -20 T(For 20 tubes)
Model Acm-54096- W -36 T(for 36 tubes)
Equipment supplied with tubes temperature controllers and racks.
 

Product Details:

Weiber Kjeldahl Units have a minimum of 3 mantles and a maximum of 6 mantles which are made of a knitted layer of glass fabric combined with flexible heating element, encased in Mild Steel housing. Over and above this layer of glass fabric accommodating the flexible heater, another layer of glass cloth is placed on the lower mantle held firmly by a circular aluminum ring. Temperature ranges form ambient to 350ºC controlled by a Sun Vic Energy Regulator with either a single control or individual controls, with corresponding indicating lamps.
 
The Weiber Ditillation Units are provided with a fume duct which is held by clamps (provided with the unit) suspended on a stand having mobility for both horizontal and vertical movements.
 
The Weiber Digestion Units are provided with the above features along with a condensing tank with individual condensing taps.
 
The Digestion And Distillation Combined Units have the features of both Digestion and Distillation which are placed on a painted MS angle stand with their respective controls. Supplied without any glass parts.

Product Details:

This chromatogram viewing cabinet combines both long and short wave ultra violet and also white light in a compact table-top unit. This self-contained unit is designed for easy viewing and marking of chromatograms and also for general fluorescence studies.

 

Chromatograms can be viewed with 3600-4000Ao long wave or 2500Ao short wave ultra violet or with white light. The ultra violet lights can also blew used in combination if desired.

 

Black curtain on the front ensure darkness and brilliant fluorescence inside the cabinet, at the same time enabling the operator to adjust the samples and lights easily or marking the fluorescent spots.

 

Features:

• Cabinet for Chromatographic analysis by ultra violet fluorescence.
• Fluorescence analysis under laboratory lighting condition.
• Fast, simple and convenient operation with independent controls at tops.
• Long wave and short wave lamps plus white light provides three means of locating and identifying components

 

Construction:

Sturdy metal construction and provided with two handles at the sides for transportation. Switches and starters are fitted at the top for easy operation.

Applications:

• Long wave : Fluorescing Spots on chromatograms can locate compounds like dyestuffs, vanillins, flavones, alkaloids etc.

• Short wave: Detects compounds, such as barbiturates, purine and pyrimidine derivatives, PTH-aminoacids, DNP-amino acids and steroids.

• In detection of traces of minerals, study of old inspections forgeries, chemical erasures, stains etc.

• The cabinet finds application in quality control especially with pharmaceuticals, electronics and industrial fabrication materials

 

 

Product Details:

WEIBER wrist action shaking machine Action is used for vigorous shaking of various solutions/chemicals in wrist action mode by conical flask fitted in the clamps. these machines are well integrated with the heavy cast iron base which make these sturdy in construction, have two equipped arms used for holding flasks fixed for shaking liquid solutions.

 

Special Features:

• Rugged construction, with timer, rated for continuous use
• Shaking speed action is variable, simulating a snap-wrist motion, but the oscillations are constant at 380 to390 per minute
• Degree of agitation, gentle to violent, is controlled by an adjustable lever with dial graduated from 1 to 10
• Power unit has constant-speed motor and built-in timer, range to 60 minutes in 1-minute intervals
• Timer 0-30 minutes (optional)

 

Product Details:

WEIBER rotary flask shaker serves its Applications in various research laboratories for shaking the liquid in glass flasks. It is a compact bench top model unit. Heavy platform is fitted with rubber discs to hold conical flasks from 50 ml to 1000ml capacity. The shaker is mounted on ball bearing crankshafts to give an orbital circular motion to the flasks. The diameter of the orbit is approximately 2. The entire assembly is mounted on a rental casing which houses a motor coupled by means of V belt with pitch pulleys.

Technical Specifications:

Product Details:

Water distillers produce highly treated and disinfected water for laboratory usage. The distillation process removes minerals and microbiological contaminants and can reduce levels of chemical contaminants.The complete unit is made of Stainless Steel with triple vapour baffle. The lid is automatically sealed with water forming is a recess in the head of the still into which the flange of lid rests which minimises the loss of steam.

 

Working Prinicple:

A water distiller works by boiling water into water vapour, condensing it and then returning it to its liquid state. It is collected in a storage container.

Water distillers are neither intended to treat water that is visually contaminated nor intended to convert waste water to safe, microbiologically.

The process occurs in several steps:

• Municipal or well water is manually or automatically fed into the distiller unit’s boiling chamber.
• A heating element in the boiling chamber heats the water until it boils.
• The steam rises from the boiling chamber. Volatile contaminants (gases) are discharged through a built-in vent.
• Minerals and salts are retained in the boiling chamber as hard deposits or scale.
• The steam enters a coiled tube (condenser), which is cooled by cool water.
• Water droplets form as condensation occurs.
• The distilled water is collected in a storage tank. If the unit is an automatic model, it is set to operate to fill the storage tank.

 

Construction Details:

Made of heavy gauge stainless sheet inside and outside, with immersion type heaters. The still provides continuous supply of pyroxene free distilled water and is equipped with brackets for wall mounting plug and cord and connector.

• Output 2 ltr/hour
• Output 4 ltr/Hour
• Output 6 ltr/Hour

 

Applications:

• Steel Manufacturing Units
• Ferrous and Alloy Steel Foundries
• Forging Units
• Wire drawing Units
• Quality Control Testing laboratories

 

Standard Capacity:

 

 

 

 

Product Details:

Water distillers produce highly treated and disinfected water for laboratory usage. The distillation process removes minerals and microbiological contaminants and can reduce levels of chemical contaminants.
 
Water distillers are neither intended to treat water that is visually contaminated nor intended to convert waste water to safe, microbiologically.
 
Working Principle:
A water distiller works by boiling water into water vapour, condensing it and then returning it to its liquid state. It is collected in a storage container.
The process occurs in several steps:

Municipal or well water is manually or automatically fed into the distiller unit’s boiling chamber.

A heating element in the boiling chamber heats the water until it boils.

The steam rises from the boiling chamber. Volatile contaminants (gases) are discharged through a built-in vent. Minerals and salts are retained in the boiling chamber as hard deposits or scale.

The steam enters a coiled tube (condenser), which is cooled by cool water.

Water droplets form as condensation occurs.

The distilled water is collected in a storage tank. If the unit is an automatic model, it is set to operate to fill the storage tank.

 
Construction Details:
A free standing unit capable of producing pyrogen free distilled water as per IP/BP standards .All contact parts are made of stainless steel mounted on a sturdy MS tubular stand
 
Standard Capacity:
CapacityOutput Load2 ltr2.0 KW4 ltrs4.0 KW6 ltrs6 KW10 ltrs10.0 KW20 ltrs15.0 KW50 ltrs25.0 KW100 ltrs50.0 KW200 ltrs72.0 KW400 ltrs130.0 KW600 ltrs200.0 KW
 
 

Product Details:

Product Introduction (Digital Brix Refractometer)
WEIBER digital handheld refractometer are used for measuring refractive index of a material.

The DRB Series digital brix refractometers are highly accurate and precise optical instruments. These digital refractometers use latest and precise optical cells. These refractometers use digital picture processing technique and accurate temperature compensation.

Advanced microprocessor is center of the digital brix refractometer which measure the brix of the liquid with precisions displays as three and half figures number liquid crystal displayer. The refractometer is simple to operate and easy to carry. This equipment is very sturdy and have a long battery life.

When a reading is shown to two decimal places, the accuracy of measurement is +/-0.1
 
Special Features:

Precise optical cells and intelligent digital picture processing technique insure accurate and stable measurement.

Accurate temperature compensation ensures exact revision in wide range of measuring temperature.

Low power consumption circuit design,

Intelligent power management and automatic switch off.

Low Voltage alarm

Unit Conversion Facility Centigrade degree and Fahrenheit degree

Easy Four Button Operation for the complete proce

3 ½ Digital LCD display

Water Proof Circuit

Strong Shock Absorption Capability

Highly consistent and reliable

Easy—to read LCD display

 
Working Principle:
Light from LED light source is focused on the underside or a prism element. When a liquid sample is applied to the measuring surface of the prism, some of the light is transmitted through the solution and lost, while the remaining light is reflected onto a linear array of photodiodes creating a shadow line. The refractive index is directly related to the position of the shadow line on the photodiodes. Once the position of the shadow line has been automatically determined by the instrument, the internal software will correlate the position to refractive index, or to another unit of measure related to refractive index, and display a digital readout on an LCD or LED scale.
 
Applications:

Food Industry: Our Digital Brix Refractometer is used in the food industry for measuring the approximate amount of sugars in fruits, vegetables, juices, wine, soft drinks and in the sugar manufacturing industry. Different countries use the scales in different industries. Our digital brix refractometers calculate the Brix value based on refractive index. These meters are portable, splash proof and very simple to use, so that they can be operated by anybody directly on location.

More and more often Brix is measured to determine ideal harvesting times of fruit and vegetables so that products arrive at the consumers in a perfect state or are ideal for subsequent processing steps such as vinification

SCIENTIFIC USAGE: When a refractometer is used, it is correct to report the result as "refractometric dried substance" (RDS). One might speak of a liquid as being 20 °Bx RDS. This is a measure of percent by weight of TOTAL dried solids and, although not technically the same as Brix degrees determined through a specific gravity method, renders an accurate measurement of sucrose content since the majority of dried solids are in fact sucrose. When an infrared Brix sensor is used, it measures the vibrational frequency of the sugar molecules, giving a Brix degrees measurement.

 

Product Details:

Microscopes are primarily employed to produce enlarged images of small object. Monocular Microscope consists of only one lens. Weiber designed monocular microscopes are built from high quality materials producing high quality enlarged image offering higher degree of resolution.It is equipped with higher achromatic objective lens, white fluorescent illumination system, high quality LED illuminator with advanced technology and ergonomic design.

 

Applications:

• Biology
• Biotechnology
• Microbiology
• Biochemistry
• Zoology
• Schools And Colleges
• Research

 

Product Details:

Working with live cells involves providing some sort of medium to facilitate the growth of these cells. Whether this involves petri dishes or some other vessels, this necessitates a live cell microscope (tissue culture cell microscope) that will accommodate them. It also requires microscope objective lenses with longer working distances to be able to focus on the live cells through the bottom of these vessels.The WEIBER tissue culture microscopes can provide any combination of modalities for live cell work including brightfield, phase contrast, and fluorescence, or any combination of these modalities.

Product Details:

Stereoscopic Zoom Binocular Microscope offers high point, lockable eyepieces and ergonomically located zoom control. Application areas include industrial and medical, Pathology and forensic applications. The microscope comes with versatile illumination system that provides both incident (top) lighting and transmitted (bottom) illumination. This microscope offers crystal clear sharp stereo images, large zoom magnification range and large working distance. Its 45° inclined binocular head ensures an easy observation and rubber eyeguards provide further comfort. This microscope is great for the exploration of the world of surface details and fine structures of various materials like wood, metal, solder, semiconductor and gemstone. It is perfect for the examination of insects, plants, rocks, stamps, jewel, soldered points, microelectronic components, circuit boards or virtually any three dimensional objects.

Features:

• Multi-Coated Optics
• Two Wide Field Eyepieces
• Two Objective Lenses (allow to see close things in 3D)
• Solid Metal Construction
• Rack and Pinion Focus Mechanism
• One Year Warranty

Product Details:

Our laboratory ball mill takes care of any pulverizing, milling or grinding job that you can give it. Its multifunction design allows it to handle wet or dry, brittle or fibrous materials. Weiber Ball mills are fitted with FHP motor. The unit drives with maximum speed of 80 rpm. The jar is made of aluminum and having steel balls of different sizes to be put in jar for mixing and grinding pesticides powder. Jar is interchangeable and easily removable, light in weight and compact unit working on 200 volts AC.

 

Working Principle:

The sample material is primarily crushed by the high-energy impact of grinding balls together with friction between the balls and the wall of the grinding bowl.

 

The grinding bowls with material and balls rotate around their own axis on a counter-rotating supporting disc. The centrifugal forces caused by the rotation of the grinding bowls and supporting discs work on the contents of the grinding bowls. The force resulting from rotation of the grinding bowl when the mill is started causes the rotating balls to rub against the inside wall of the bowl thus crushing the material.

 

At a certain point in time the stronger centrifugal force of the supporting disc causes the grinding material and balls to separate from the inner wall of the grinding bowl. The grinding balls cross the bowl at high speeds impacting with the grinding material on the opposite wall - creating size reduction by impact.

Product Details:

WEIBER Hot Plates are useful for sealing, pre-heating, re-flow, and processing under controlled temperature conditions. Three models are available:

MODEL-I

Body made of M.S. sheet duly stove painted / powder coated fitted with coil type heating element suitable to work on 220/230 volts A.C. Supply. Rating 1.5 KW, 7½" Diameter.i) With 3 heat switch.ii) With E.R. Regulator Control.

MODEL-II

Deluxe quality with heavy cast iron base duly heat resistant painted. Rating 1.5 kw fitted with ER Control or thermostat controller, fibre blanket insulated with kanthal ISI heater and fire proff conection.i) With 3 heat switchii) With E.R. Regulator Control.

MODEL-III

Rectangular Hot Plate with outer M.S. sheet body duly powder coated or stove painted. To work on 220/230 volts A.C. supply useful for continuous heating up to 350ºC. Heavy duty Cast Iron Top, Ceramic Blanket Insulated Top with heat resistant paint.

Round hot plate:

The body is made of P.C.R.C. sheet duly painted with attractive stove enamel. The top cost iron heating plate is round having 20 cm dia, with heating elements of 1.5 KW rating. Temperature is controlled by energy regulator upto 3500C.

 

Size Available:

• a) 10 x 12 x 6 (250x300x150mm)
• b) 16 x 10 x 6 (400x250x150mm)
• c) 18 x 24 x 6 (450x600x150mm)
• Available with Thermostate / Energy Regulator Contrl and with Digital Temperature Controller.

 

Product Details:

Weiber Diaphragm type Vacuum Pump is designed for fast, efficient operation. Its large, powerful composition pulls an automotive air conditioning system into a deep vacuum in record time. Just hook it up to the vehicle, plug it in, and it removes both air and moisture rapidly, assuring thorough dehydration before you recharge. It works on both R-134a and R-12 vehicles with no changeover or waiting time! An industrial strength motor insures long lasting reliability and operation. It can also be integrated into many RTI refrigerant management centers.

 

Salient Features:

• Compact Design
• Low Noise Level.
• Maintenance Free.
• Easy to handle.
• Continuous Duty.
• Totally Dry Compressed Air.
• Low Running Cost

Applications:

• Chemical Industry
• Air Conditioning
• TV tube manufacturing
• Vacuum testing
• Vacuum Lifting
• Distillation
• Filtration
• Impregnation
• Vacuum Coating
• Freeze Drying

 

Product Details:

Dry air/low humidity environment is essential in varied application in research laboratories, seed storage facility, and pharmaceutical industry and in various other industrial and specific research applications.

Our De humidifiers are ideal to remove excess moisture from the atmosphere of a given laboratory/work place/storage facility.
Air Dehumidifiers are designed to suit unique moisture/humidity control needs during processing, packaging, drying and storage. It features unique Zexter-00908 technologically advanced dehumidification coil which has the ability to extract.

Product Features:

• Micro processor controlled System
• Extremely Silent
• Defrost automatically when the ambient temperature is below 18 deg.c.
• Backward air outlet
• Full Water Tank Warning
• Adjustable air direction
• Non-touch point tank full switch
• Provided with castor wheels
• Easy Movement across the house hold
• Continuous drainage
• Corrosion Resistant Casing
• R-134a CFC-Free Refrigerant
• Power Reciprocating Compressor

 

Working Principle:

Weiber dehumidifier removes moisture from the air, thus lowering the humidity. It does this by condensing water onto a cold surface. A fan is used to speed up the process. It blows warm air onto cold metal coils, and the resulting water drips into a water collector. The resulting cold air is then passed over warm coils to bring it back to room temperature. The air is then reheated and sends back to the room.

 

Applications:

Dry Air Storage (Multi Purpose) :

In dry air storage our dehumidifier keeps the relative humidity at the desired level all year round regardless of the temperature. Basic dry air storage only requires an un insulated, reasonably airtight, building fitted with a dehumidifier. Steel and other metals, wood, paper, pulverized products, military equipment are just a few examples of items possible that can be stored safely and at low cost.

Production Facilities (Pharmaceutical):

Weiber dehumidifiers make it possible to produce pharmaceutical products all year round in a controlled dry atmosphere. These dehumidifiers increase production capacity in spray dryers and fluidized beds that are used, for example, in the food industry. Breweries can avoid mould and condensation on cold surfaces by using dehumidifiers

Archives:

Archives for photographic film must be kept at low temperature and at low relative humidity, typically + 2 ºC, 30% RH. A controlled climate with stable relative humidity is also vital to prevent art collections, old documents, textiles, books etc from being damaged by the ravages of time.

Power Plants And Buildings:

Being able to supply dry air inside industrial facilities and buildings is an important capability. Power plant boilers, piping, steam condensers, turbines and bridges are examples of dry air corrosion protection methods. Buildings that have suffered flooding or moisture damage can often be made fully functional again after drying out with dry air.

Product Details:

This group of magnetic stirrers is similar to the conventional magnetic stirrers but have additional hot plate to achieve heating of solutions to be stirred. The heating is controlled by energy regulator, which ensures regulation at any desired percentage of the capacity of heater.

Product Details:

We offers table Rotap Sieve Shaker assists in producing uniform motion for shaking. It is used for research and development, quality control of raw materials, as well as in production monitoring.

 

A horizontal circular motion overlies a vertical motion which is created by a tapping impulse. These motional processes are characteristic of hand sieving and produce a higher degree of sieving for denser particles (e.g. abrasives) than throw-action sieve shakers

 

Technical Specifications:

Rotap Sieve Shaker is driven by ¼ H.P. Electricx motor through a reduction gear, can carry upto SIX , 6 OR 8 /12 /18 Test Sieves with one set of LID AND Pan . This Rotap motion of the table is an upward and downward movement but is inclined from the vertical axis and the direction or inclination charges progressively in clockwise direction having frequency of about 270 vibration per minutes. Unit having six Stainless Steel needles fixed on Stainless Steel pipe of approx 12.5 mm dia with side water tap. Tank made of Stainless Steel. (with timer/without timer).

 

Applications:

• Pharmaceutical
• Cosmetic
• Chemical and food processing industries

 

Product Details:

The objective of the wet sieve test is to obtain basic index information about the soil, that can be used to estimate strength and permeability. It is the primary form of classification for granular soils.

 

There are some materials which, when tested dry, produce less than accurate particle analysis results. If the material is not soluble in water and reproducible results are difficult to obtain, then wet testing may be the method required to produce accurate data. This kit offers an alternative to hand wet wash sieving using a single tall-frame wet wash sieve. It has been specifically designed for use with the Weiber wet Ro-Tap sieve shaker and a stack of standard full-height testing sieves.

 

Working Principle:

A gradation test is performed on a sample of aggregate in a laboratory. A typical sieve analysis involves a nested column of sieves with wire mesh cloth (screen). A representative weighed sample is poured into the top sieve which has the largest screen openings. Each lower sieve in the column has smaller openings than the one above. At the base is a round pan, called the receiver.

 

The column is typically placed in our wet sieve shaker. The shaker shakes the column, usually for some fixed amount of time. After the shaking is complete the material on each sieve is weighed. The weight of the sample of each sieve is then divided by the total weight to give a percentage retained on each sieve.

 

The size of the average particles on each sieve then being analysis to get the cut-point or specific size range captured on screen.

 

The results of this test are used to describe the properties of the aggregate and to see if it is appropriate for various civil engineering purposes such as selecting the appropriate aggregate for concrete mixes and asphalt mixes as well as sizing of water production well screens.

 

 

Product Details:

We offers table Gyratory Sieve Shaker assists in producing uniform motion for shaking. It is used for research and development, quality control of raw materials, as well as in production monitoring.

 

Working Principle:

A horizontal circular motion overlies a vertical motion which is created by a tapping impulse. These motional processes are characteristic of hand sieving and produce a higher degree of sieving for denser particles (e.g. abrasives) than throw-action sieve shakers

Benefits of Using an Automated Test Sieve Shaker for Particle-Size Analysis:

• More Consistent and Accurate Results- The first mechanical test sieve shaker was designed to replicate the hand motions used in manual testing scenarios. By automating this process, test sieve shakers are able to provide a much higher level of continuity throughout the testing process. As a result, they can produce more accurate and repeatable results regardless of when or where a test is performed.
• Increased Efficiency- Manually shaking test sieves is both time consuming and labor intensive. A mechanical sieve shaker is able to replicate and replace the human input needed to perform this type of testing. This means that more material can be tested in less time and with fewer resources invested.
• Cost Savings- Employing humans to conduct these tests represents ongoing costs in the form of wages and fringe benefits. In addition, downtime related to illness or personal absences also translates into lost productivity and increased opportunity cost. The modern shaker is both reliable and durable. As a result, it doesn't require a lot of expensive maintenance or need replaced often. Over time, these factors can translate into substantial cost savings

 

Product Details:

The complete soxhlet extraction apparatus consists of solvent reservoir extraction assembly with 6 extraction places with concentric metal rings of various diameter to suit 100 ml flasks to 250 ml flasks and built in steam generator. Complete with stand, clamp holder soxhlet extraction (Condenser) glass and extraction flask of 60 ml volume.
 
Temperature Control:
Temperature is controlled through electronic solid state temperature controller cum indicator or micro processor based digital temperature controller cum indicator or hydraulic thermostat with energy regulators.
 
Stantdard Model:
Unit of 3 test Mantle Type (With or without glass parts & clamps)
Unit of 3 test Heater Type (With or without glass parts & clamps)
Unit of 6 test Mantle Type (with or without glass parts & clamps)
Unit of 6 test Heater Type (with or without glass parts & clamps)
 

Product Details:

Weiber manufactured Water softener systems are primarily designed for water treatment and various other industrial water treatment purposes. Water softeners can be equipped to operate manually, semi or fully-automatically. Regardless of the set up, only limited technical expertise is required for operation. Water softening is the removal of calcium, magnesium, and certain other metal cations in hard water. Water softening is usually achieved using ion-exchange resins. Industrial water softener systems offer a wide variety of optional features to meet our customers' requirements.

 

They are available in a wide range of self-contained packages configured in single, double and triple unit arrangements. Water softener systems equipped with advanced technology and high quality raw materials. Industrial water softeners deliver excellent performance in an ergonomically designed construction.

 

Special Features:

• Available with single or dual stainless steel propellers
• Continuous duty
• 1/3, 1/2, 3/4, 1, 1 1/2, 2, 3, & 5 horsepower bracket mount styles
• 1/3, 1/2, 3/4, 1 & 1 1/2 horsepower clamp mount styles
• TEFC, explosion proof or air powered motors
• Factory wiring, topical coating, variable shaft lengths & other options available

 

Construction Details:

• The Industrial Steel Tank Automatic Water Softener (SF-100S Series) softeners are designed as fully automatic units either with timer or meter control. The timer control initiates softener regeneration at any predetermined time - on any or every day. The metered models start regeneration based on the total gallons used.
• The steel mineral tank is engineered for a 100 psi working pressure and is tested to 150 psi. It is equipped with a manhole in the upper dome.
• The interior of the tank is coated with epoxy for protection against rust and corrosion. The exterior has a rust inhibiting primer coat.
• A premium grade sulfonated nonphenolic polystyrene type resin is contained in the mineral tank. The resin will deliver 30,000 grains per cubic foot when brined at a rate of 15 lbs. per cubic foot.
• The brine tank is a combination of high density polystyrene brine measuring tank and a brine valve, including an air eliminator valve and a safety brine refill shut off to prevent tank overflow.
• The automatic regeneration controller features a choice of 7 or 12 day calendar wheels. Time of regeneration and length of time for each regeneration cycle are fully adjustable.
• The under drain utilizes either a hub & lateral or a header & lateral system to evenly distribute water and prevent resin loss, and to insure minimal pressure drop at peak flow rates.

 

Applications:

Water softeners offers ideal applications for water softening equipment in areas such as Apartments/Condominiums, Car Washes, Boiler Feed water, Hospitals, Laundries, Manufacturing Plants, Office Complexes, Institutions, Food Processing Plants, Restaurants.

 

 

Product Details:

Weiber industrial saphire-1000 series Reverse Osmosis systems are designed and manufactured for dependable service, they can provide packaged water quality with output capacities ranging from 1000 LPH. These systems are ideal for small and medium-sized water stores or bottling operations. our systems will output water is in 10 to 30 PPM TDS range.

 

Working Principle:

The various processing stages involved in RO system are:

 

The equipment required for these various stages can be purchased "stand-alone", or separately, if needed. More usuallywe will supply an integrated, or "turnkey" system, in which the needed stages and equipment are pre-connected and tested.

The process occurs in several steps:

• Preconditioning Stage

  The proper preconditioning of your water is critical to the smooth and safe operation of your business. Improperly treated input water can cause serious damage to the various components of your reverse osmosis system, and would surely compromise the quality of your product water.

  A complete analysis of your incoming water supply is essential. This will determine what elements are present and what pre-treatment is necessary to remedy any problems

• A typical standard preconditioning package consists of:

  Multi-media filter to remove sediment and particulate matter

  Carbon filter to remove any organic chemicals (chlorine, pesticides, etc.)

  These systems are available "stand-alone" or as part of a "turnkey" package.

  In some cases, additional preconditioning may be needed. For example, the presence of bacteria or iron in the incoming water would require treatment with ultraviolet light and specialized iron filters, respectively.

• RO Stage

  The main focus of our commercial reverse osmosis systems is the small to medium-sized water store or bottling operation.

• Disinfection Stage

  The disinfection stage is an essential component of any drinking water processing operation. Since the water exiting the reverse osmosis system will be stored in a closed tank, it is susceptible to stagnation and biological contamination. To remedy this, some combination of Ultraviolet and/or Ozone disinfection is required. As in the preconditioning stage, this equipment can be purchased "stand-alone" if needed. However, some of the reverse osmosis systems we supply (see below) are optionally configurable with UV and Ozone modules.

 

Standards Features:

Made of heavy gauge stainless sheet inside and outside, with immersion type heaters. The still provides continuous supply of pyroxene free distilled water and is equipped with brackets for wall mounting plug and cord and connector.

• Compact design requires minimal installation space
• Designed for municipal/tap water source
• Quality components utilized for system construction
• Designed for optimum water recovery
• Adjustable waste and recycle flow controls
• Quick and easy system installation
• Available for pressure or open tank applications
• Vertical Heavy Duty Pump
• Complete Stainless Steel Housing
• Tfc membrane, PVC housing
• Liquid-filled system pressure gauge
• Pressurized tank pressure gauge
• Adjustable. Waste/recycle valves
• High-pressure nylon tubing
• High-pressure brass comp. Fittings
• Storage tank pressure switch
• Low-pressure switch
• Feed water inlet solenoid valve
• Rotary vane pump
• Suitable sediment pre-filter
• Suitable carbon block pre-filter

 

Product Details:

In laboratories for many analytical & biological procedures, analysis and instruments pure water is needed. This pure water is identifies in terms of laboratory grade water which is measured in water Resistivity. Resistivity is determined by the amount of ionic contaminations and by its Total organic CARBON Content. WEIBER RO+UV units are one such system which facilitates pure water according to ASTM standards.

 

Special Features:

• Type 2 RO, easy to operate & maintain.
• Suitable for Tap water (corporation water) and post RO.
• Compact system including Reverse Osmosis technology with super charge deionization resin to produce high quality
• laboratory – grade pure water.
• Easy to install.
• Designed to fit your space requirements.
• Effective membrane filtration that removes all types of water contaminations.
• Membrane is maintaining due to the manual flushing cycles.
• Pre treatment to prevent the membrane from scaling formation.
• The built in UV lamp is ideal for applications that require low bacteria levels.
• Online Conductivity meter to ensure the required water quality.

 

Working Principle:

PRE – TREATMENT : TO PROTECT THE SYSTEM

Spun Cartridge Filter

The micron cartridge filter is provided for fine filtration of suspended solids. Filter is good for the removal of relatively uniform sized particles throughout the body of the filter.

When to Replace a Filter Cartridge

As particles accumulate on a filter cartridge, flow through the filter becomes restricted. This restriction reduces the flow rate through the cartridge and increases backpressure Thus the Cartridge filter should be changed when the flow drop or pressure drop is considerable.

Granular Activated Carbon

The granular activated carbon to eliminate free chlorine and colloids present in tap water that may otherwise alter the taste and color of your water supply.

Spun Cartridge Filter

The micron cartridge filter is provided for fine filtration of suspended solids.

MEMBRANE TECHNOLOGY : TO REMOVES ALL DISSOLVED INORGANIC & ORGANIC IMPURITIES

Reverse Osmosis System a) RO Membrane

The membranes used have spiral configuration i.e. osmotic membranes are wrapped in a coil around central manifold.

b) Membrane Housing Vessel

The membrane is housed in ABS suitable for one element of standard size.

Permeate Rota meter

Allows the user to check the flow rate of RO permeate water.

Booster Pump

The pump is used where there is a mains pressure of 0.5 bars or less.

Ultra Filtration.

Ultra filtration is separation process using membrane with pore size in the range between 0.1 to 0.012 micron. Typically ultra filtration will remove high molecular substance colloidal materials and organic and inorganic polymeric molecules.

U.V. System

UV system for very low bacteria levels. Type 2 RO water system can be equipped with a UV system .water is sanitized through a 254 nm UV lamp in a stainless steel housing. UV lamps kill any live bacteria & microorganisms.

Mix Bed Resin

The resin filters are a very high quality Semiconductor grade mixed bed resins that remove the last of the Ions from the RO water. The mixed bed resin removes the dissolved ions of various minerals from the water to bring the water resistively up to 0.1 Ω. This is what gives the final polish to the water.

 

Product Details:

With WEIBER RO+UV+DI range of water purification systems, you benefit from a compact solution that efficiently combines reverse osmosis technology, UV filtration and deionization resins to produce pure water. It produces high quality water with very low energy consumption. The use of "low energy" membranes enable a very efficient and economical operation. These systems are equipped with a built-in 6 l storage tank. Pure water is collected in the tank and is recirculated by an integrated pump.

 

We can customize RO+UV+DI systems according to the capacities required.

 

Special Features:

• Pure water circulation right into the dispenser head
• Easy to dispense water using the practical POU dispenser
• 0.2 µm sterile filter with or without endotoxins retention as option available
• Whisper operation mode
• Rapid and simple disinfection
• Conductivity monitoring of RO and DI water
• Easy module exchange via quick-release connections

 

Pathway:

• Booster Pump
• Inlet Solenoid Valve
• Pretreatment
• RO Reject Solenoid Valve
• RO Reject Capillary
• Check Valve and RO Permeate Conductivity Cell
• Ion Exchange Polisher Cartridge
• Product Resistivity Cell
• UV Lamp 254 nm (UV System)
• 6-Liter Reservoir

Applications:

• PCR
• IC
• Pathology
• Cytology + histology work
• Buffer preparation
• Photometry and spectrophotometry
• Media preparation
• Electrophoreses
• General Chemistry
• Feed for laboratory ultra-pure water systems
• Final Rinse of laboratory washing machines

 

 

Product Details:

Deionizers (DI) remove both cations and anions, releasing hydrogen ions (H+) in exchange for the former, and hydroxyl ions (OH-) for the latter. The hydrogen and hydroxyl ions subsequently combine to form pure water.

 

Deionizers are most commonly used when ionic contamination is such that reverse osmosis alone cannot be relied upon to produce water of acceptable quality. In such most instances, mixed bed deionizers may be placed downstream of the reverse osmosis unit, completing the purification process.A wide variety of public water vending machines as well as many industrial applications in the electronics industry operate in this manner.

 

Special Features:

• Optional recirculation pumps
• Parallel or Series Regeneration
• Programmable purge prior to regeneration
• 12 or 24 volt operation (120/60hz/1pH transformer included)
• Custom programmable for automatic precision and simplicity.
• Delivers duplex DI water more economically than any other deionizer.
• The most advanced DI control package available.
• The digital-type meter displays both water quality and regeneration time remaining .
• A third tank polisher can be accommodated under the single control to pick up sodium or silica leakage, allowing you to easily attain higher purity water at less expense.
• A single set of printed circuit boards control both simultaneous and sequential regeneration. You simply select the desired regeneration mode with DIP switches.
• All programming features are easily accessible on the front panel, so there's no need to enter the control box and disrupt operations.
• Modular construction reduces downtime and simplifies troubleshooting and service.
• A low level sensor can be easily wired into the control to warn of low chemical volumes.
• Provisions for a remote control panel and auxiliary "START REGENERATION" source allow regeneration to be initiated and controlled from a location remote from the actual installation site.
• Level controlled shutoff to a product storage tank can be utilized with the addition of a simple float switch in the storage tank.
• Relays and fuses on the power printed circuit board provide for the operation of recirculation and supply pumps.

 

Working Principle:

The two-bed deionizer consists of two vessels - one containing a cation-exchange resin in the hydrogen (H+) form and the other containing an anion resin in the hydroxyl (OH-) form. Water flows through the cation column, whereupon all the cations are exchanged for hydrogen ions.To keep the water electrically balanced, for every monovalent cation, e.g. Na+, one hydrogen ion is exchanged and for every divalent cation, e.g. Ca2+, or Mg2+, two hydrogen ions are exchanged. The same principle applies when considering anion-exchange. The decationised water then flows through the anion column. This time, all the negatively charged ions are exchanged for hydroxide ions which then combine with the hydrogen ions to form water (H2O).

 

Construction Details:

It consists of an in-built pre filter and very high exchanging capacity non-corrosive CATION and ANION resin columns pre-fitted with imported RESINS for efficient results having treated water parameters conforming to IS- 1069/64. It yields chemically pure water equal to multiple distilled water having a conductivity of less than 10 micro siemens / cm and pH of 7.5 to 9pH. Fitted with sturdy PVC multi-control valve and connected direct to water taps. The conductivity meter operates on both AC supply and 9.0 V DC battery. Supplied with one plastic chemical proof regeneration tank and the complete unit in housed in a painted M.S. trolley for easy mobility. Available with analogue as

 

Product Details:

Binocular microscopes provide better images and are good for long-time observation. Binocular microscopes have two eye-tubes. Weiber binocular microscope is easy-to-use microscopes which comes equipped with a binocular head. The binocular microscope is especially useful for use in the medical field, lab work, and any educational institute.

 

Binocular research microscopes are of ergonomic design suitable for most applications in transmitted light microscopy. This model display a state of the art understanding of operator requirements and comfort. The quadruple revolving nosepiece is carefully positioned so that it face inward and objectives pointing away from the user so that they will not interfere with operator. It is equipped with CF contrast LB objectives having monolayer coatings to reduce internal reflection, thus ensuring high contrast image

 

Applications:

• Education and Research
• Medical Labs

 

Product Details:

An advanced versatile projection microscope for measurement of specimens, different types of yarns in textile industries and research institutes. It is equipped with Halogen bulb of 12V/100 watt workable through a solid state built in transformer working on 220V AC mains.

 

Features:

• Condenser: A high quality glass condenser in front of screen.
• Mechanical Tube: Length 160 mm
• Nose piece: Triple revolving nose piece.
• Movement: Coarse motion through rack and pinion with precise and accurate fine movement. Fixed square stage 102 x 102 mm.
• Lamp Assembly:

  Fixed lamp, built in base of high illumination with high power condenser and screen it will work as micro view projector.

  With lamp, transformer, but without it will work as microscope.

  The viewing of biological microscope slides is distinct and enlarged. Sharp, clear and evenly illuminated image in full colors, visible to the whole class free of distortion. Supplied in polished wooden box having lock and key.

 

Product Details:

WEIBER table Top Sieve Shaker assists in producing uniform motion for shaking. The vibration is controlled by speed regulator. It is used for research and development, quality control of raw materials, as well as in production monitoring.

 

Working Principle:

The vertical throwing motion is overlaid with a slight circular motion which results in distribution of the sample amount over the whole sieving surface. The particles are accelerated in the vertical direction (are thrown upwards). In the air they carry out free rotations and interact with the openings in the mesh of the sieve when they fall back. If the particles are smaller than the openings, they pass through the sieve. If they are larger, they are thrown upwards again. The rotating motion while suspended increases the probability that the particles present a different orientation to the mesh when they fall back again, and thus might eventually pass through the mesh.

 

Applications:

The size distribution is often of critical importance to the way the material performs in use. A sieve analysis can be performed on any type of non-organic or organic granular materials including sands, crushed rock, clays, granite, feldspars, coal, soil, a wide range of manufactured powders, grain and seeds etc.

 

 

Product Details:

Features:

Useful for accelerated mixing of solutions in test tubes, small flasks or centrifugal tubes etc.

• The speed is regulated by a speed control device.
• hort eccentric stroke motor imparts vigorous agitation to the tubes or flasks.
• Sturdy construction and finished in enamel paint.

Product Details:

A Trinocular microscope is equipped with three eyepieces to offer better resolution of the product image. The WEIBER Trinocular microscope comes with continuous adjustable magnifications. Trinocular port enables the addition of photographic or video capability. With super wide field, high-eye point eyepieces, it gives sharp and crystal clear images with high resolution. It offers large zoom ranges and long working distances.

A line of eleven Plano-apochromatic objectives (long and super-long working distances models available) is designed for use in the visible wavelengths. They are corrected for chromatic aberration in the red, yellow, and blue, and provide good color reproducibility.

 

Special Features:

• The Trinocular microscopes have a built-in transmitted illumination system.
• The precise focusing mechanism allows both coarse and fine focus adjustments, to yield crisp, clear images. Imaging is also aided by a fiber optic light guide that provides bright field illumination.
• The 50/50 Trinocular microscope head allows for simultaneous video and binocular viewing. The focusing 10X or 20X wide field eyepieces can accept 25-mm diameter reticules for measurement applications.
• The reverse nosepiece can hold up to four objectives, allowing a range of magnifications. The instrument has a 1X to 2X zoom range.
• The objectives are available in a range of magnifications from 2X (with a numerical aperture (NA) of 0.055 and a working distance of 34 mm), to 200X (with a NA of 0.62 and working distance of 13 mm).

 

Product Details:

These rotary oil sealed pumps are quiet operating and vibration less designed for continuous duty and factory tested to assure a satisfactory performance. The pump mechanism is contained in metal case with oil level sight gauge and drains plug at base. Motor driven pumps are completely mounted on rectangular base plate and are furnished with V belt, Single stage. S-25 Displacement Ltr / Min 25, Motor H.P. 0.25.

Air Displacement :

• 25 Liters / Minutes
• 50 Liters / Minutes
• 100 Liters / Minutes
• 150 Liters / Minutes
• 200 Liters / Minutes
• 300/400/500/750 liters/minutes

 

Applications:

• Evacuation of Vacuum Systems
• Bulbs
• Neon Signs
• A.C.and Refrigeration
• Vacuum flasks
• Transformers
• Vacuum Moulds
• Drying
• Filling
• Lifting
• Forming
• Bright Annealing
• Impregnation
• Filtration
• Distillation
• Leak-Testing

 

 

Product Details:

Glass Water distillation units produce highly treated and disinfected water for laboratory usage. The distillation process removes minerals and microbiological contaminants and can reduce levels of chemical contaminants.

Water distillers are neither intended to treat water that is visually contaminated nor intended to convert waste water to safe, microbiologically.

 

Special Features:

• Demountable boiler.
• Compact design.
• Dual safety cutout (optional).
• High purity,Low conductivity, Pyrogen free distillate.
• Easy service and maintenance due to Demountable model.
• Quartz distiller instead of glass (optional)

 

Working Principle:

A water distiller works by boiling water into water vapour, condensing it and then returning it to its liquid state. It is collected in a storage container.

The process occurs in several steps:

• Municipal or well water is manually or automatically fed into the distiller unit’s boiling chamber.
• A heating element in the boiling chamber heats the water until it boils.
• The steam rises from the boiling chamber. Volatile contaminants (gases) are discharged through a built-in vent. Minerals and salts are retained in the boiling chamber as hard deposits or scale.
• The steam enters a coiled tube (condenser), which is cooled by cool water.
• Water droplets form as condensation occurs.
• The distilled water is collected in a storage tank. If the unit is an automatic model, it is set to operate to fill the storage tank.

 

Construction Details:

The distillation apparatus consists of flask with heating elements embedded in glass and fused in spiral type coil internally of the bottom and tapered round glass, joints at the top double walled condenser with B-40/B-50 ground glass joints, suitable to work on 220 volts, 50 cycles AC supply.

 

Applications:

For Distillation of Water (General & Lab Use)

 

 

 

Product Details:

Electrically operated to work on 220 Volts A.C Recommended for grinding of dry plant samples. Also for a great variety of commercial dry materials. Unit having two stationary steel blades and Rotary with steel edges provided in the cast Iron chamber. A removable safety Glass sheet plate from the face of chamber of permits observation during operation. Willey Mill is fitted on substantial Cast iron base. Complete unit supplied with aluminum / Cast chamber , polished hopper with cover, wooden plugger, Three delivery tubes mounted with sieves cloth mesh no; 20, 40, and 60mesh , One Allen Key for adjusting blades and 3 Glass Jars, brush etc.

 

Size Available: