Bath & Chillers

Product Details:

WEIBER Oil Bath, is a type of heated bath which uses boiling oil as the temperature regulator. Since different oils have different boiling points it is possible to obtain a temperature near to the desired temperature by selecting an oil with a boiling point as close as possible to the desired temperature. The most common oils that are being utilized in oil baths are paraffin, glycerol, silicon oil or cottonseed oil due to their quite odorless characteristics.

 

Double Walled High Temperature Oil Bath is having wide range of application, such as oxidation stability test on oils, greases, etc, or any other test requiring high temperature control having high thermal efficiency. This oil bath was developed for a wide range of testing and meets ASTM specifications for Methods D471, D865, and D1313.

 

Special Features:

• Interior construction of stainless steel 304
• Outer construction-PCRC sheet /SS 304 (as per requirement)
• 75mm glass wool insulated on five sides
• Provided with High speed stirrer with speed regulator
• Control panel provided on the side of oil bath two neon lights and an ON/OFF switch.
• Perforated and removable diffuser shelves
• Microprocessor based temperature controller
• Aesthetically designed-Designed according to the standards and principles underlining industry’s aesthetic values.
• Corrosion Resistant interior and exteriors-Corrosion resistant coatings like epoxy coatings are applied inside and outside the baths to prevent against degradation due to moisture, salt spray, oxidation or exposure to a variety of environmental or industrial chemicals/ corrosive agents.
• Energy Efficient – the baths uses less energy to provide the same level of performance, comfort and convenience, thus making it energy conserving.
• Sturdy Construction – the baths are built with robustness to withstand stress and strain, giving it long life and ability to perform in extreme stress environments.

 

Product Details:

A water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. WEIBER water baths are widely used for day to day bacteriological and varied laboratory applications requiring incubation as well as general tests and procedures in variety of research and testing laboratories.

 

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

 

Sailent Features:

• Versatile usage
• Ergonomic Design
• Energy Efficient
• Long life
• Low Maintenance
• Calibration And Protocol Documentation
• PID temperature controller
• Aesthetically designed-Designed according to the standards and principles underlining industry’s aesthetic values.
• Corrosion Resistant interior and exteriors-Corrosion resistant coatings like epoxy coatings are applied inside and outside the baths to prevent against degradation due to moisture, salt spray, oxidation or exposure to a variety of environmental or industrial chemicals/ corrosive agents.
• Energy Efficient – the baths uses less energy to provide the same level of performance, comfort and convenience, thus making it energy conserving.
• Sturdy Construction – the baths are built with robustness to withstand stress and strain, giving it long life and ability to perform in extreme stress environments.

 

Optional Features:

• HMI+PLC based controller
• Printer report program
• RS 232/485 interface
• USB ports
• Real time data acquisition system
• profile control(MULTIPLE PROGRAMMING)
• timer (1 to 999min)
• Over temperature alarm system.

 

Construction Details:

Water baths are double walled convection heated units. Outer body of our water baths are constructed out of thick PCRC steel sheet/SS 304 (as per request) duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings.

Heating: Indirect heating system is provided in our water bath, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring very good temperature sensitivity.

Temperature Range: Temperature range of our standard water bath models are 5o c above ambient to 90o c. However we have the capacity to modify the same to suit the individual specialized requirements of our customers.

Temperature Sensitivity: Temperature inside our water bath is controlled with a sensitivity of + 0.5o c or better.

Front Panel: Front panel of our water bath comprises of on/off switches heating and mains indicator lamps and temperature controller.

 

Applications:

• Laboratory Applications
• Warming of reagents
• Melting of substrates
• Incubation of cell cultures
• Bacterial examination
• Crude oil analysis
• Food processing
• Immunology testing
• Protein analysis
• Thawing samples
• Warming samples
• General chemical and biological uses

 

 

 

Product Details:

Mash Bath are designed for laboratory use in breweries and malt houses. It aids in the determination of malt extract. The equipment allows one to utilize the CONGRESS, HARTONG 20, HARTONG 45, HARTONG 65, HARTONG 80, ASBC, PROFILE or THERMOSTAT methodology of testing. The Thermostat method maintains a constant temperature for a specific time. The Profile method allows the user to program the variables to suite their needs.

Special Features:

• Microprocessor based temperature control (HMI+PLC as an option)
• Programmable delayed start
• Audible alarm
• Low level water cut out
• Accurate water dispense (+/- 5ml) to all beakers in less than 2 min
• RS 232/485 interface (optional)
• Timer (optional)
• Real time data acquisition system (optional)
• USB ports (optional)
• Printer report program (optional)

 

Working Principle:

Congress-Method:

• Mashing, by passing through a temperature program
• Use of malt-fine grind and –coarse grind
• Detection of the absolute number of the extract content, by use of the Plato-Table. In addition to the identification of the
• scarification time (Iodine- normality), protein content, viscosity, pH-value . Difference between fine- and coarse grind extract,
• permits a conclusion to the cytolytical solution of the malt

Hartong-Method:

• Mashing at constant temperature (20°, 45°, 65° or 80° C)
• Use of malt-fine grind
• Detection of a ratio (VZ) = percentage share of the highest possible extract yield at the chosen temperature. Conclusions about the enzyme activity, protein modification of the malt and malting work by itself, are possible.

Constructions Details:

• Our mash bath is superiorly made up of epoxy coated PCRC sheet/SS 304 (as per requirement) and inner stainless steel chamber.
• Beakers in the bath are stirred using magnetic followers driven by electric motors beneath the bath.
• An integral pump circulates water through the heater box and bath
• Temperature is controlled by nanotechnology based ergonomic controller (HMI+PLC optional)
• Temperature range: 20°C to 95°C
• mixer speed: 0, 100, 200 rpm
• beaker options: 5,6,8,10,12,16,20,25
• Distilled water for mashing is heated in a separate stainless steel accumulator and dispensed to the beakers by an electric pump.
• The bath is designed to be fully automatic although some of the operations can be done manually. Manual control of the water fill valve, the water drain valve and each motor stirring bank are all possible.

 

Applications:

• Breweries
• Malt houses
• laboratories

 

 

Product Details:

Weiber Calibration temperature baths provide optimal temperature environments for “secondary” or “comparison” temperature calibrations. They offer unsurpassed stability and uniformity, a large working volume, and flexibility for performing thermometer calibration on calibrating a variety of temperature sensors. It not only allows calibration of multiple systems at the same time, but also offer the added advantage of accommodating sensors of all shapes and sizes.These high temperature baths provide calibration temperature upto300°C.

 

Calibration baths are stable to ±0.001 °C and do not require calibration blocks or use of special calibration techniques to achieve that stability. Standard as well as customized models are available.

 

Special Features:

• Large-capacity tanks for higher productivity
• Calibrations up to 300 °C
• Built-in cooling coils for faster cooling
• The units are operated via an innovative and user friendly control panel which includes an LCD display, and offer configurable PID controller (HMI+PLC as an option)
• Visual and audible alarms in the event of a failure
• Dual protection system against uncontrolled over-temperature events:
  • Heating elements turn off automatically if measured temperature exceeds the set threshold by 5°C
  • Mechanical over-temperature device shuts off heating elements if temperature exceeds maximum allowed values
• Variety of liquids that can be used

	Type	Marking	Temperature range
1	Denatured Ethanol	DE	-90°C….0°C
2	Silicone oil	KDC 200.05	-40 °C ÷ 130 °C
3	Water	W	10 °C ÷ 95 °C
4	Silicone oil	KDC 200.20	10 °C ÷ 230 °C
5	Silicone oil	KDC 200.50	30 °C ÷ 278 °C

• RS 232/485 interface (optional)
• USB ports (optional)
• On off updates on mobile (optional)
• Real time data acquisition system (optional)
• Corrosion resistant inner and outer surfaces.
• Sturdy construction
• CFC free refrigeration unit, for low temperature requirements

Construction Details:

• The outer construction of calibration bath is epoxy painted PCRC sheet/SS 304(as per requirement).
• The inner chamber is constructed out of high grade SS-304.
• The temperature is controlled by nanotechnology based ergonomic controller
• Temperature range: -30 to 300OC. however we can modify the same as per requirement.
• Cooling unit: the cooling unit comprises of CFC free compressors of Kirloskar/Tecumseh / Bitzer/ Danfoss make, conforming to latest international standards and guidelines.

 

Product Details:

WEIBER Recirculating chillers are the ideal solution when you need precise temperature control or cooling below ambient temperature. A compressor-based recirculating chiller offers outstanding performance and high reliability as well as quiet operation and ease-of-use. These chillers are used for controlled cooling of products, mechanisms and factory machinery in a wide range of industries.

 

hey are often used in the plastic industries , injection and blow molding, metal working, welding equipment, die-casting and machine tooling, chemical processing, pharmaceutical formulation, food and beverage processing, paper and cement processing, vacuum systems, X-ray diffraction, power supplies and power generation stations, analytical equipment, semiconductors, compressed air and gas cooling. They are also used to cool high-heat specialized items such as MRI machines and lasers, and in hospitals, hotels and campuses.

 

Special Features:

• Splash-proof key pad with integrated mains switch
• Felling level indicator
• Powerful immersion pumps, suitable for continuous operation
• Easy filling form the top with hinged protective lid
• Low liquid level protection with optical and audible alarm signal
• Removable venting grid for cleaning of the condenser
• RS232 interface for PC-connection (Optional)
• Calibration And Protocol Documentation
• Air cooled refrigeration unit
• CFC free refrigerant
• Microprocessor based temperature controller (HMI+PLC as an option)
• USB ports (optional)
• Real time data acquisition system (optional)
• compatible with a variety of fluids depending on operating temperatures

Construction Details:

Our re-circulating chillers are double walled convection heated units. Outer body of our re-circulating chiller is constructed out of thick PCRC steel sheet/SS 304 (as per requirement), duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings.

• HEATING

Indirect heating system is provided in our chiller, comprising of air heaters made of high grade Kanthal A-1wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural waterconvection mechanism, ensuring a very good temperature sensitivity.



• COOLING UNIT

An energy efficient cooling unit is installed in our recirculatory chiller. We use ISI marked high end CFC free compressors of Kirloskar / Tecumseh make, conforming to latest international standards and guidelines.

DETAILED DESCRIPTION ALONG WITH SALIENT FEATURES ARE AS UNDER FOR REFRIGERATION MACHINE


CONDENSING UNIT

(1) AIR-COOLED CONDENSOR

Air-cooled condenser is internally grooved finned copper tubes used for high heat transfer area, which not only reduce power consumption, but also bring down the condensation faster. This unit is designed. & verdigris & reduces the resistance, saves energy consumption and ensure good heat exchange.




(A.) COMPRESSOR:

HERMETIC COMPRESSOR

Single stage Reciprocating Compressor. Give the High Efficiency compared to sealed compressors, Less Power Consumption , Accessible for repairing, low noise level, Less Vibrations, Wide Voltage Range, Designed for Extremely High Ambient ,Full warranty etc.


COOLING SYSTEM

The compressor is mounted perfectly to ensure recommended level of sound and vibration.

 

Product Details:

The WEIBER Refrigerated Fluid Chiller System cools various fluids such as water, water/glycol or oil down to, or below, the ambient temperature. These provide Stable and reliable cooling for many common heat removal applications, including laser etching, AA furnaces, ICP, rotary evaporators, vacuum systems, reaction vessels, plasma etching and condenser cooling. It can achieve cooling capacity of 2KW, 1.8KW, 1.6KW and 1.4KW, for diversity of applications.

 

Whether integrated into a machine or used as an auxiliary cooler, this system will tackle any cooling task and guarantees quality with utmost precision.

 

Special Features:

• Equipped with solenoid valve, pressure controller for safe, Silent and efficient refrigeration.
• Liquid level indication sight window and pressure gauge help you observe the circulating and cooling process going the way as expected.
• Over temperature protection
• Air cooled condenser
• RS232 interface for PC-connection (Optional)
• Calibration And Protocol Documentation
• Microprocessor based temperature controller (HMI+PLC as an option)
• USB ports (optional)
• Real time data acquisition system (optional)
• compatible with a variety of fluids depending on operating temperatures
• low noise level
• sturdy construction
• CFC free refrigeration unit

 

Construction Details:

Our refrigerated chillers are double walled convection heated units. Outer body of our re-circulating chiller is constructed out of thick PCRC steel sheet, duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings.

• HEATING

Indirect heating system is provided in our chiller, comprising of air heaters made of high grade Kanthal A-1wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural waterconvection mechanism, ensuring a very good temperature sensitivity.



• COOLING UNIT

An energy efficient cooling unit is installed in our recirculatory chiller. We use ISI marked high end CFC free compressors of Kirloskar / Tecumseh make, conforming to latest international standards and guidelines.




DETAILED DESCRIPTION ALONG WITH SALIENT FEATURES ARE AS UNDER FOR REFRIGERATION MACHINE

CONDENSING UNIT

(1) AIR-COOLED CONDENSOR

Air-cooled condenser is internally grooved finned copper tubes used for high heat transfer area, which not only reduce power consumption, but also bring down the condensation faster. This unit is designed. & verdigris & reduces the resistance, saves energy consumption and ensure good heat exchange.




(A.) COMPRESSOR:

HERMETIC COMPRESSOR

Single stage Reciprocating Compressor. Give the High Efficiency compared to sealed compressors, Less Power Consumption , Accessible for repairing, low noise level, Less Vibrations, Wide Voltage Range, Designed for Extremely High Ambient ,Full warranty etc.


COOLING SYSTEM

The compressor is mounted perfectly to ensure recommended level of sound and vibration.


(B.) REFRIGERATION CONTROL

(a).Low and High Pressure switch of RANCO/Danfoss




Which ensures the compressor and refrigeration system when low pressure will occurs it trip off the compressor. This is the only operator friendly switch can easily reset.

 

 

 

Product Details:

Standards Compiled:

• ASTM E715-80
• ASTM F2473-12
• BS 619:1935
• BS 4525:1983
• ISO 759-1981

 

Salient Features:

• Versatile usage
• Ergonomic Design
• Energy Efficient
• Long life
• Low Maintenance
• Calibration And Protocol Documentation
• Microprocessor based temperature controller (HMI+PLC as an option)

 

Working Principle:

Circulatory water baths have an in-built pump/circulator which pumps the bath liquid externally into an instrument and back into the bath. Circulating water baths are designed to circulate heated liquid around the tank, providing a more uniform heat transfer for samples.

 

Construction Details:

Water baths are double walled convection heated units. Outer body of our re-circulating chiller is constructed out of thick PCRC steel sheet, duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings.

• Heating:

Indirect heating system is provided in our water bath, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring very good temperature sensitivity.

• Temperature Range:

Temperature range of our standard water bath models are 5o c above ambient to 100o c. However we have the capacity to modify the same to suit the individual specialized requirements of our customers.

• Temperature Sensitivity:

Temperature inside our water bath is controlled with a sensitivity of + 0.5o c or better.

• Front Panel:

Front panel of our water bath comprises of on/off switches heating and mains indicator lamps and temperature controller.

 

Applications:

• Enzymatic and serologic experiments.

 

 

Product Details:

Salient Features:

Versatile usage

Ergonomic Design

Energy Efficient

Long life

Low Maintenance

Calibration And Protocol Documentation

PID based temperature controller (HMI+PLC as an option)

Aesthetically designed- Designed according to the standards and principles underlining industry’s aesthetic values.

Corrosion Resistant Interior and Exteriors- Corrosion resistant coatings like epoxy coatings are applied inside and outside the baths to prevent against degradation due to moisture, salt spray, oxidation or exposure to a variety of environmental or industrial chemicals/ corrosive agents.

Energy Efficient – The baths uses less energy to provide the same level of performance, comfort and convenience, thus making it energy conserving.

Sturdy Construction – The baths are built with robustness to withstand stress and strain, giving it long life and ability to perform in extreme stress environments.

Printer report program(optional)

232/485 interface (optional)

USB ports (optional)

Real time data acquisition system (optional)

profile control(MULTIPLE PROGRAMMING) (optional)

timer (optional)

Construction Details:
Serological water baths are double walled convection heated units. Outer body of our water baths are constructed out of SS 304/ PCRC steel sheet (as per request) duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings.

Heating:
Indirect heating system is provided in our water bath, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring very good temperature sensitivity.

Temperature Range:
Temperature range of our standard water bath models are 5o c above ambient to 90o c. However we have the capacity to modify the same to suit the individual specialized requirements of our customers.

Temperature Sensitivity:
Temperature inside our water bath is controlled with a sensitivity of + 0.5o c or better.

Front Panel:
Front panel of our water bath comprises of on/off switches heating and mains indicator lamps and temperature controller. The unit is fitted with a high efficiency stirrer motor of 1/20 HP, so as to maintain the uniform temperature of our high precision water bath.
 
Applications:

Serological pharmaceutical, biomedical procedure

Research laboratories

 
Standards Complied:

ASTM E715-80

ASTM F2473-12

BS 619:1935

BS 4525:1983

ISO 759-1981

 
 
 

Product Details:

Pycnometer is a device used to calculate density of a semi solid or liquid. WEIBER pycnometer test baths are specifically designed for incubating pycnometers bottles upto 2000ml.

 

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

 

Special Features:

• Versatile usage
• Ergonomic Design
• Energy Efficient
• Long life
• Low Maintenance
• Calibration And Protocol Documentation
• CFC free refrigeration unit
• Microprocessor based temperature controller (HMI+PLC as an option)
• Printer report program (optional)
• RS 232/485 interface (optional)
• USB ports (optional)
• Real time data acquisition system (optional)
• profile control(MULTIPLE PROGRAMMING) (optional)
• timer (optional)

 

Construction Details:

 

Pycnometer baths are double walled convection heated units. Outer body of our re-circulating chiller is constructed out of thick PCRC steel sheet, duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings.

• Heating:

Indirect heating system is provided in our bath, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring very good temperature sensitivity.

• Temperature Range:

Temperature range of our standard bath models is-5°C to 80°C. However we have the capacity to modify the same to suit the individual specialized requirements of our customers.

• Temperature Sensitivity:

Temperature inside the bath is controlled with a sensitivity of + 0.5°C or better. (PID controller)

• Cooling

An energy efficient cooling unit is installed in our recirculatory chiller. We use ISI marked high end CFC free compressors of Kirloskar / Tecumseh make, conforming to latest international standards and guidelines.

DETAILED DESCRIPTION ALONG WITH SALIENT FEATURES ARE AS UNDER FOR REFRIGERATION MACHINE

CONDENSING UNIT

(1) AIR-COOLED CONDENSOR

Air-cooled condenser is internally grooved finned copper tubes used for high heat transfer area, which not only reduce power consumption, but also bring down the condensation faster. This unit is designed. & verdigris & reduces the resistance, saves energy consumption and ensure good heat exchange.

 

 

 

Product Details:

WEIBER nitrogen evaporators (water bath type) are typically used “to concentrate samples before analysis or to concentrate samples before a solvent exchange.When a scientist needs to concentrate a sample that’s in a volatile liquid—like acetone, acetonitrile, or methanol—a nitrogen evaporator can do the job. As a result, scientists use this technology in sample preparation in environmental, polymer science, quality control, and toxicology labs etc.Our nitrogen evaporators utilize adjustable nitrogen blow down technology allowing full control of nitrogen flow to samples, with no wasted nitrogen gas. We combined this technology with uniform efficient heat applied through water baths. This simultaneously maximizes solvent evaporation in the samples being concentrated and saves the lab money.

 

The 24 position WEIBER nitrogen evaporator is our most adaptable version but we can customize it to 6/12/34/50 positions as per the requirement.

 

Special Features:

• Microprocessor based control system.
• Can accommodate samples with an outside diameter of 10-30 mm.
• Provides controlled concentration of sample vials through the application of nitrogen gas within a heated water bath.
• The dual band spring hoist assembly provides a simple and effective means of removing samples from the heated water bath.
• Circular rotating design permits each sample to be accessible from the front of the instrument for easy insertion and retrieval.
• The chrome plated needle valves are individually milled from solid brass, enabling precise, uniform adjustments for your nitrogen blow down.
• Efficient and safe sample reduction with minimal nitrogen waste.
• Long lasting and user friendly technology
• Gas flow can be controlled at each sample position via needle valves
• Nitrogen filter
• High pressure phthalate free tubing for safety, Teflon tubing for no contamination
• Needles, 4 inch x 19 gauge with polypropylene hub and stainless steel shaft
• 220v wiring harness (optional)
• Z-Purge/intrinsically safe purge case (optional)
• Acid resistant coating on instrument and needles (optional)
• Side control box with built-in digital controller, timer, and pressure regulator (optional)

Product Details:

A water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. WEIBER reciprocating shaking water bath has an extra control for shaking, which moves liquids around. Shaking feature can be turned on or off. It is designed for a wide range of temperature-controlled shaking protocols, such as Northern and Southern Hybridization, Destaining of gels, Incubation of cells or bacterial cultures as well as Wash Processes. The temperature range, which goes up to 99°C also allows you to use the bath as a Boiling Bath.

 

The Shaking Water Bath is equipped with a PID Controller for easy temperature selection, rapid heat up and excellent stability. A high quality, robust design with a unique shaking mechanism that allows you to easily switch from orbital mode to reciprocating mode by simply reversing the tray.

 

Special Features:

• Microprocessor control with digital LED display and shaker control
• Set temperature (in increments of 0.1°C) and oscillation speed via control-panel touchpad for entry of temperature and shaking speed
• Shaking frequency: 30 to 200 oscillations/min.
• Stroke length adjustable at 0.5, 1.0 or 1.5in. (13, 25 or 38mm)
• Microprocessor-controlled proportional integral temperature control and solid-state sensing probe provide excellent temperature sensitivity
• over temperature protection capability
• Automatic motor shutdown capability
• with adjustable high-limit thermostat and indicator light
• Rugged stainless-steel interior with easy-to-clean epoxy powder-coated exterior
• HMI+PLC controller (option)
• Printer report program(optional)
• RS 232/485 interface (optional)
• USB ports (optional)
• Real time data acquisition system (optional)
• profile control(MULTIPLE PROGRAMMING) (optional)
• timer (optional)

Product Details:

WEIBER refrigerated circulatory water bath are able to reach temperature as low as -40OC. it provides dependable temperature control for a wide variety of laboratory cooling applications.Circulating water baths (also called stirrers ) are ideal for applications when temperature uniformity and consistency are critical, such as enzymatic and serologic experiments. Water is thoroughly circulated throughout the bath resulting in a more uniform temperature.

Salient Features:

• Versatile usage
• Ergonomic Design
• Energy Efficient
• Long life
• Low Maintenance
• Calibration And Protocol Documentation
• Microprocessor based temperature controller (HMI+PLC as an option)
• Printer report program(optional)
• RS 232/485 interface (optional)
• USB ports (optional)
• Real time data acquisition system (optional)
• profile control(MULTIPLE PROGRAMMING) (optional)
• timer (optional)

 

Construction Details:

Water baths are double walled convection heated units. Outer body of our water baths are constructed out of SS 304/ PCRC steel sheet (as per request) duly pre-treated with primers for rust proofing and painted with air drying paint/stove enamel/powder coating. The inside chamber of the unit is made of heavy gauge stainless steel sheet of grade ss-304. The unit is provided with top opening cover, made of stainless steel with steel concentric rings

• Heating:

Indirect heating system is provided in our bath, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring very good temperature sensitivity.



• Temperature Range:

Temperature range of our standard water bath models are -40°C to 100°C. However we have the capacity to modify the same to suit the individual specialized requirements of our customers.



• Temperature Sensitivity:

Temperature inside our water bath is controlled with a sensitivity of + 0.5°C or better.



• Cooling Unit:

the cooling unit comprises of CFC free compressors of Kirloskar/Tecumseh / Bitzer/ Danfoss make, conforming to latest international standards and guidelines.




DETAILED DESCRIPTION ALONG WITH SALIENT FEATURES ARE AS UNDER FOR REFRIGERATION MACHINE


CONDENSING UNIT

(1) AIR-COOLED CONDENSOR

Air-cooled condenser is internally grooved finned copper tubes used for high heat transfer area, which not only reduce power consumption, but also bring down the condensation faster. This unit is designed. & verdigris & reduces the resistance, saves energy consumption and ensure good heat exchange.




(A.) COMPRESSOR:

HERMETIC COMPRESSOR

Single stage Reciprocating Compressor. Give the High Efficiency compared to sealed compressors, Less Power Consumption , Accessible for repairing, low noise level, Less Vibrations, Wide Voltage Range, Designed for Extremely High Ambient ,Full warranty etc.

COOLING SYSTEM


The compressor is mounted perfectly to ensure recommended level of sound and vibration.

(B.) REFRIGERATION CONTROL


(a).Low and High Pressure switch of RANCO/Danfoss




Which ensures the compressor and refrigeration system when low pressure will occurs it trip off the compressor. This is the only operator friendly switch can easily reset.


(b).Hand Shut off Valve

Is the only Condensing Unit, which is equipped with it. This valve is used for pump down the total gas in to the condenser & receiver in the faulty condition.

 

Product Details:

Pycnometer is a device used to calculate density of a semi solid or liquid. WEIBER pycnometer test baths are specifically designed for incubating pycnometers bottles upto 2000ml.

 

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.

 

Special Features:

 

• Interior construction of stainless steel 304
• Outer construction-PCRC sheet (as per requirement)
• 75mm glass wool insulated on five sides
• Provided with High speed stirrer with speed regulator
• Control panel provided on the side of oil bath two neon lights and an ON/OFF switch.
• Perforated and removable diffuser shelves
• Microprocessor based temperature controller (HMI+PLC as an option)
• Printer report program (optional)
• RS 232/485 interface (optional)
• USB ports (optional)
• Real time data acquisition system (optional)
• Profile control(MULTIPLE PROGRAMMING) (optional)
• Timer (optional)

 

Construction Details:

• The outer construction of oil bath is corrosion resistant PCRC sheetwith epoxy coating.
• The inner construction is of high grade SS-304
• 75 mm high grade mineral glass wool insulation
• Long life nickel plated heating elements are removable for ease in cleaning the tank.
• Temperature range & Controller: Temperature range from 5°C above ambient to 400°C. Microprocessor temperature and set point readout and over temperature protection are standard.

 

Applications:

• Research
• Test labs
• Quality control

 

Standard Complied:

• ASTM D471
• ASTM D865
• ASTM D1313
• ASTM D972-02(2008)

 

 

 

 

 

Product Details:

Water cooled chiller is a refrigeration apparatus that produces cold water or water/glycol mix, to cool industrial process equipment or provide comfort cooling for buildings. A water chiller uses the evaporation of a refrigerant to cool the fluid through a heat exchanger. Weiber offers a large selection of water cooled chillers/heater with quality construction and innovative technology, serving a variety of industries. The size and type of equipment used varies from small pre-packed low temperature environmental chambers of only a few horsepower (kW) to large custom-designed and often field-erected systems ranging to several hundred horsepower (kW).

 

The larger units are by nature one-of-a-kind, designed and built for a specific purpose, for a specific duty at a precisely controlled low temperature condition. The large units use a combination of one, two or more refrigerants in open cascade arrangements to obtain the desired low temperature. 7 standard models are available to choose from however we have the capacity to customize the specification as per individual needs.

 

Special Features:

• Precision temperature stability
• Special fluid handling (materials, pumps, filtration)
• Portable and reliable
• Ergonomic designs
• Microprocessor based controller (HMI+PLC based controller option)
• CFC free refrigeration system
• Hermetically sealed compressor
• RS 232 interfacing for remote control and monitoring
• Options for recirculating fluids (see the technical matrix of all models)
  • Water
  • Deionized Water
  • Deuterium Oxide / Methanol
  • Fluorinert FC-3283
  • Ethylene Glycol
• Front to rear airflow
• Audio visual alarms for malfunction
• Castors for ease in mobility

 

Construction Details:

The heavy duty frame is constructed of welded steel tubing mounted on locking casters.

HEATING

Indirect heating system is provided in our chiller, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring a very good temperature sensitivity.

COOLING UNIT

An energy efficient cooling unit is installed in our chiller. We use ISI marked high end CFC free compressors of Kirloskar / Tecumseh make, conforming to latest international standards and guidelines.

TEMPERATURE RANGE

Temperature range of our chiller models vary for different models (see the technical matrix.) how ever we have the capacity to change the temperature specifications as per requirement

 

Applications:

• Biotech
• Aerospace
• Automotive
• Semiconductor
• medical industries
• plastic industries
• printing industries
• laser cutting industries

 

 

 

Product Details:

WEIBER industrial chillers (air cooled) is a refrigeration system used to cool a process fluid and dehumidifies air in industrial facilities. Air cooled chiller uses fans to dissipate the heat removed by the refrigeration system. The equipment works as an air conditioning system with the world's best standard A-type screw compressor and newly designed shell and tube heat exchanger that have powerful cooling ability, low noise, low vibration, high efficiency and high reliability. These are equipped where no source of liquid are available for cooling the condenser.

Air Cooled Chiller comes complete with PID microprocessor-controlled controller that utilizes fully proportional cooling and heating. The equipment offers low-stress refrigeration system, circulating pumps, R-134A CFC free refrigerant and fluid reservoir. WEIBER gives you an option to choose from the seven models as per the desired recirculating fluid and other technical parameters.We specialize in both standard as well as customized chillers to meet the demands in required areas.

 

Standards Compiled:

• ARI 590
• NFPA 70
• NFPA 79
• BS EN 1048:1999
• BS EN 1048:2014
• ASHRAE 90.1

Special Features:

• Multi Channel Systems for multiple cooling loop applications
• Precision temperature stability
• Special fluid handling (materials, pumps, filtration)
• Portable and reliable
• Ergonomic designs
• Microprocessor based controller (HMI+PLC based controller option)
• CFC free refrigeration system
• Hermetically sealed compressor
• RS 232 interfacing for remote control and monitoring
• Options for recirculating fluids (see the technical matrix of all models)
  • Water
  • Deionized Water
  • Deuterium Oxide / Methanol
  • Fluorinert FC-3283
  • Ethylene Glycol
• Front to rear airflow
• Audio visual alarms for malfunction
• Castors for ease in mobility
• Safety devices
• suitable for use in both closed loop and ground loop water-source
• equipped with rotary screw compression
• equipped with includes particle filters, DI filters, water resistivity probes and rotary flow meters

Construction Details:

The heavy duty frame is constructed of welded steel tubing mounted on locking casters.

HEATING

Indirect heating system is provided in our chiller, comprising of air heaters made of high grade Kanthal A-1 wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring a very good temperature sensitivity.

COOLING UNIT

An energy efficient cooling unit is installed in our chiller. We use ISI marked high end CFC free compressors of Kirloskar / Tecumseh make, conforming to latest international standards and guidelines.

TEMPERATURE RANGE

Temperature range of our chiller models vary for different models (see the technical matrix.) how ever we have the capacity to change the temperature specifications as per requirement

 

Applications:

• Biotech
• Aerospace
• Automotive
• Semiconductor
• medical industries
• plastic industries
• printing industries
• laser cutting industries

 

 

Product Details:

WEIBER now introduces special baths that uses ultrasound (usually from 20–400 kHz) and an appropriate cleaning solvent (sometimes ordinary tap water) to clean items. The contaminants can be dirt, oil, grease, buffing/polishing compounds, and mold release agents. Ultrasonic bath is powerful enough to remove tough contaminants, yet gentle enough not to damage the substrate. It provides excellent penetration and cleaning in the smallest crevices and between tightly spaced parts in a cleaning tank.

 

Our digitally controlled ultrasonic baths offer consistent and reliable performance in a variety of environments such as laboratory, scientific and healthcare. Incorporating frequency LEAP technology to ensure uniform levels of ultrasonic activity throughout the fluid, these baths offer vastly improved performance giving a more accurate and precise ultrasonic process.

 

Special Features:

• Frequency LEAP technology provides more homogeneous ultrasonic activity throughout the tank, reducing dead spots and standing waves
• Temperature range from Heated ambient +5ºC to 70ºC
• SD port allows easy validation tracking between bath and PC.
• Improved software memory logs cleaning parameters allowing easy cycle repeatability and easytraceability of cycle number, time, temperature and Sonics validation
• Easy to use digital LCD control panel with user - settable parameters to suit individual requirements.
• Accurate process control of time, temperature, ultrasonic activity, degas and power
• Stainless steel basket - designed specifically to generate maximum ultrasonic activity, prevent items resting on the tank and prevent operators coming into contact with chemical solutions. Included as standard.
• Ergonomic ABS plastic lid - reduces noise volume and minimizes potential of aerosol escape. Included as standard.
• Drain valve for convenient emptying
• Clean finish, high-quality and robust design for long-term reliability and durability.
• Analogue timer (digital timer optional)
• Digital microprocessor based temperature controller

 

Construction Details:

 

The outer construction of ultrasonic baths are constructed out of corrosion resistant epoxy painted mild steel .whereas the interior chamber is made of industrial grade stainless steel (SS-304.)

• Utrasound generation

In order to produce the positive and negative pressure waves in the aqueous medium, a mechanical vibrating device is required. Our ultrasonic baths incorporates Piezoelectric transducers. These transducers can be welded directly into the tank

• Temperature control.

The temperature is maintained through digital microprocessor based ergonomic controller (PID controller)

• HEATING

Indirect heating system is provided in our baths, comprising of air heaters made of high grade nichrome wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring a very good temperature sensitivity.

 

Applications:

• Healthcare/Clinical - the first stage of the decontamination process for reusable surgical instruments in dental, podiatry and general practice settings
• General use - glass, equipment, component cleaning, sonication of cytometer nozzles, dispersion and solubilization
• Laboratories - cleaning of components, degassing fluids, mixing fluids and compounds, cell disruption, fluid dissolution
• Biopharma - dissolution of samples

 

 

Product Details:

WEIBER now introduces special baths that uses ultrasound (usually from 20–400 kHz) and an appropriate cleaning solvent (sometimes ordinary tap water) to clean items. The contaminants can be dirt, oil, grease, buffing/polishing compounds, and mold release agents. Ultrasonic bath is powerful enough to remove tough contaminants, yet gentle enough not to damage the substrate. It provides excellent penetration and cleaning in the smallest crevices and between tightly spaced parts in a cleaning tank.

 

Our Industrial range of ultrasonic cleaners is robust and long lasting, providing the user with excellent and repeatable cleaning performance. Incorporating a digital control panel and integral heating system, the bath is supplied complete with stainless steel lid and basket. IT has been designed to be incorporated into manufacturing and routine maintenance programmes where the highest standards are essential.

 

Special Features:

• Temperature range from Heated ambient +5ºC to 70ºC
• SD port allows easy validation tracking between bath and PC.
• Improved software memory logs cleaning parameters allowing easy cycle repeatability and easytraceability of cycle number, time, temperature and Sonics validation
• Easy to use digital LCD control panel with user - settable parameters to suit individual requirements.
• Accurate process control of time, temperature, ultrasonic activity, degas and power
• Stainless steel basket - designed specifically to generate maximum ultrasonic activity, prevent items resting on the tank and prevent operators coming into contact with chemical solutions. Included as standard.
• Ergonomic ABS plastic lid - reduces noise volume and minimizes potential of aerosol escape. Included as standard.
• Drain valve for convenient emptying
• Clean finish, high-quality and robust design for long-term reliability and durability.
• Analogue timer (digital timer optional)
• Digital microprocessor based temperature controller

 

Construction Details:

The outer construction of ultrasonic baths are constructed out of corrosion resistant epoxy painted mild steel .whereas the interior chamber is made of industrial grade stainless steel (SS-304.)

Utrasound generation

In order to produce the positive and negative pressure waves in the aqueous medium, a mechanical vibrating device is required. Our ultrasonic baths incorporates Piezoelectric transducers. These transducers can be welded directly into the tank

Temperature control.

The temperature is maintained through digital microprocessor based ergonomic controller (PID controller)

Heating:

Indirect heating system is provided in our baths, comprising of air heaters made of high grade nichrome wires of suitable wattage. The temperature is evenly distributed throughout the chamber through natural water convection mechanism, ensuring a very good temperature sensitivity.

 

Product Details:

WEIBER refrigerated baths offer a completely integrated refrigerated circulating system for open or closed applications, with a temperature range from -35°C to +100°C. Our refrigerated water baths are widely used for day to day bacteriological and varied laboratory applications requiring incubation as well as general tests and procedures in variety of research and testing laboratories including Wassermann, Kilmer tests. Apart from that, these refrigerated water baths have a variety of usages in tissue culture applications, enzyme reaction studies, growth observation studies, fermentation analysis and various other general and specialized applications in various laboratories.

 

We specialize in both standard and customized models, specifically designed to meet the challenging demands of various test areas.